Experimental investigations on a single stage centrifugal compressor showed that measured blade vibration amplitudes vary considerably along a constant speed line from choke to surge. The unsteady flow has been analyzed to obtain detailed insight into the excitation mechanism. Therefore, a turbocharger compressor stage impeller has been modeled and simulated by means of computational fluid dynamics (CFD). Two operating points at off-design conditions were analyzed. One was close to choke and the second one close to the surge line. Transient CFD was employed, since only then a meaningful prediction of the blade excitation, caused by the unsteady flow situation, can be expected. Actually, it was observed that close to surge a steady state solution could not be obtained; only transient CFD could deliver a converged solution. The CFD results show the effect of the interaction between the inducer casing bleed system and the main flow. Additionally, the effect of the nonaxisymmetric components, such as the suction elbow and the discharge volute, was analyzed. The volute geometry itself had not been modeled. It turned out to be sufficient to impose a circumferentially asymmetric pressure distribution at the exit of the vaned diffuser to simulate the volute. Volute and suction elbow impose a circumferentially asymmetric flow field, which induces blade excitation. To understand the excitation mechanism, which causes the measured vibration behavior of the impeller, the time dependent pressure distribution on the impeller blades was transformed into the frequency domain by Fourier decomposition. The complex modal pressure data were imposed on the structure that was modeled by finite element methods (FEM). Following state-of-the-art calculations to analyze the free vibration behavior of the impeller, forced response calculations were carried out. Comparisons with the experimental results demonstrate that this employed methodology is capable of predicting the impeller’s vibration behavior under real engine conditions. Integrating the procedure into the design of centrifugal compressors will enhance the quality of the design process.

1.
Rodgers
,
C.
, 2003, “
High Specific Speed, High Inducer Tip Mach Number, Centrifugal Compressor
,” ASME Paper No. GT2003-38949.
2.
Dawes
,
W. N.
, 1988, “
Development of a 3D Navier Stokes Solver for Aplication to all Types of Turbomachinery
,” ASME Paper No. 88-GT-70.
3.
Dawes
,
W. N.
, 1993, “
The Extension of a Solution Adaptive Three-Dimensional Navier-Stokes Solver Toward Geometries of Arbitrary Complexity
,”
ASME J. Turbomach.
0889-504X,
115
, pp.
283
295
.
4.
Dawes
,
W. N.
, 1995, “
A Simulation of the Unsteady Interaction of a Centrifugal Compressor With Its Vaned Diffuser: Flow Analysis
,”
ASME J. Turbomach.
0889-504X,
117
, pp.
213
222
.
5.
Domercq
,
O.
, and
Thomas
,
R.
, 1997, “
Unsteady Flow Investigation in a Transonic Centrifugal Compressor Stage
,”
AIAA J.
0001-1452
6.
Walitt
,
L.
,
Nguyen
, and
C.
,
Nyquist
,
R.
, 1997, “
Unsteady Analysis and Re-Design of a Centrifugal Compressor Stage Using a CFD Optimizer
,”
AIAA J.
0001-1452.
7.
Hunziker
R.
,
Dickmann
,
H.-P.
, and
Emmrich
,
R.
, 2001, “
Numerical and Experimental Investigation of a Centrifugal Compressor With an Inducer Casing Bleed System
,” ATI-CST-025/01,
Proceedings of 4th European Conference on Turbomachinery
,
Florence, Italy
, pp.
319
329
.
8.
Hunziker
,
R.
,
Jakoby
,
P.
, and
Meier
,
A.
, “
A New Series of New Turbochargers for High Flow Rates and High Pressure Ratios
,”
Proceedings of CIMAC Congress 2001
,
Hamburg
, Vol.
2
, pp.
321
331
.
9.
Filsinger
,
D.
,
Szwedowicz
,
J.
,
Schäfer
,
O.
,
Dickmann
,
H.-P.
, “
Pulse Charged Axial Turbocharger Turbines—A Challenge for Numerical Design Methods
,”
Proceedings of CIMAC Congress 2001
,
Hamburg
, Vol.
2
, pp.
712
722
.
10.
Fisher
,
F. B.
, 1988, “
Application of Map Width Enhancement Devices to Turbocharger Compressor Stages
,” SAE Paper No. 880794.
11.
ANSYS, Inc. 2004, CFX-5.7 User Manual.
12.
Cui
,
M.
, 2004, “
Unsteady Flow Around Suction Elbow and Inlet Guide Vane in a Centrifugal Compressor
,” ASME Paper No. GT2004-53273.
13.
Sorokes
,
J. M.
,
Borer
,
C. J.
, and
Koch
,
J. M.
, 1998, “
Investigation of the Circumferential Static Pressure Non-Uniformity Caused by a Centrifugal Compressor Discharge Volute
,” ASME Paper No. 98-GT-326.
14.
Reunanen
,
A.
,
Pitkänen
,
H.
,
Siikonen
,
T.
,
Heiska
,
H.
,
Larjola
,
J.
,
Esa
,
H.
, and
Sallinen
,
P.
, 2000, “
Computational and Experimental Comparison of Different Volute Geometries in a Radial Compressor
,” ASME Paper No. 2000-GT-469.
15.
Sorokes
,
J. M.
, and
Koch
,
J.
, 2000, “
The Influence of Low Solidity Vaned Diffusers on the Static Pressure Non-Uniformity by a Centrifugal Compressor Discharge Volute
,” ASME Paper No. 2000-GT-0454.
16.
Hagelstein
,
D.
,
Hasemann
,
H.
, and
Rautenberg
,
M.
, 1997, “
Coupled Vibration of Unshrouded Centrifugal Compressor Impellers
,”
Proc. Of the 7th Int. Symp. On Transportation Phenomena and Dynamics of Rotating Machinery
, ISROMAC-7, pp.
1306
1317
.
17.
ABAQUS User’s manual Version 6.4, 2003, ABAQUS Inc., 1080 Main Street, Pawtucket, RI 02860-4847.
18.
Filsinger
,
D.
,
Frank
,
Ch.
, and
Schäfer
,
O.
, 2005, “
Practical Use of Unsteady CFD and FEM Forced Response Calculation in the Design of Axial Turbocharger Turbines
,” ASME Paper No. GT2005-68439.
19.
Schmitz
,
M. B.
,
Schäfer
,
O.
,
Szwedowicz
,
J.
,
Secall Wimmel
,
T.
, and
Sommer
,
T. P.
, 2003, “
Axial Turbine Blade Vibrations by Stator Flow—Comparison of Calculations and Experiment
,”
10th ISUAAAT, Durham, NC, 2003
, Conf. Proc. on CD ROM.
20.
Moyroud
,
F.
,
Cosme
,
N.
,
Jöcker
,
M.
,
Fransson
,
T. H.
,
Lornage
,
D.
, and
Jacquet-Richardet
,
G.
, 2000, “
A Fluid-Structure Interfacing Technique of Computational Aeroelastic Simulations
,”
9th ISUAAAT, Lyon, France
, Conference Proceedings pp.
721
738
.
21.
Filsinger
,
D.
,
Sekavcnik
,
M.
,
Ihli
,
T.
,
Schulz
,
A.
, and
Wittig
,
S.
, 2002, “
Vibration Characteristics of a Radial Turbocharger Impeller
,”
Proceedings of the 7th Int. Conference on Turbochargers and Turbocharging, London
, pp.
117
127
.
22.
Senturier
,
E.
,
Lombard
,
J.-P.
,
Dumas
,
M.
,
Dupont
,
C.
,
Sharma
,
V.
, and
Dupeux
,
J.
, 2004, “
Forced Response Prediction Methodology for the Design of HP Compressors Bladed Disks
,” ASME Paper No. GT2004-53372.
23.
Schaber
,
U.
, 1997, “
Non-Contact Vibration Measurements of Mistuned Coupled Blades
,” ASME Paper No. 97-GT-190.
24.
Whitehead
,
D. S.
, 1988, “
The Maximum Factor by Which Forced Vibration of Blades Can Increase Due to Mistuning
,”
J. Eng. Gas Turbines Power
0742-4795,
120
, pp.
115
119
.
You do not currently have access to this content.