1-8 of 8
Keywords: nanoindentation
Close
Sort by
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Tribol. June 2024, 146(6): 061701.
Paper No: TRIB-23-1394
Published Online: February 5, 2024
... modifications and irregularities. The hardness values from the nanoindentation were measured to be 5.66 ± 0.28, 6.75 ± 0.40, and 7.34 ± 0.53 GPa for the as-built, HT-1, and HT-2 samples respectively. In accordance with Archard's wear equation, a sample with lower hardness demonstrates a higher wear-rate...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Tribol. May 2022, 144(5): 051402.
Paper No: TRIB-21-1305
Published Online: December 2, 2021
...: phd1701203005@iiti.ac.in 1 Corresponding author. Email: satyajit_ch@rediffmail.com Contributed by the Tribology Division of ASME for publication in the J ournal of T ribology . 28 06 2021 31 10 2021 31 10 2021 02 12 2021 electroless coatings nanoindentation wear...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Tribol. April 2014, 136(2): 021602.
Paper No: TRIB-13-1031
Published Online: December 27, 2013
.... 26 01 2013 18 11 2013 In the present work, nanoindentation experiments were carried out to characterize the localized transfer film layer (TFL) on a steel disk, which resulted from a sliding contact of the latter against a polymer composite pin. It was found that the hybrid...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Tribol. October 2013, 135(4): 041301.
Paper No: TRIB-12-1204
Published Online: July 3, 2013
...—hardness and elastic modulus—were examined using nanoindentation. The MTCC surfaces may be a successful alternative bearing material for artificial joints. Understanding the nanomechanical, material properties, and surface morphology of the MTCC–CoCrMo surface are important for designing wear resistant...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Tribol. January 2013, 135(1): 011001.
Paper No: TRIB-12-1017
Published Online: December 20, 2012
.... Mater. Res. , 19 ( 8 ), pp. 2356 – 2365 . 10.1557/JMR.2004.0293 [25] Koch , T. , Evaristo , M. , Pauschitz , A. , Roy , M. , and Cavaleiro , A. , 2009 , “ Nanoindentation and Nanoscratch Behaviour of Reactive Sputtered Deposited W-S-C Film ,” Thin Solid Films , 518 ( 1...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Tribol. April 2010, 132(2): 021902.
Published Online: March 11, 2010
... that two nanoindentation experiments with normal loads of 500   μ N (for tip A), 750   μ N (for tip B), and 9 mN (for tip C) were performed 1 – 2   μ m away from the start and end of each scratch. These nanoindentation marks were used as markers to clearly distinguish...
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Tribol. January 2007, 129(1): 11–16.
Published Online: June 27, 2006
...S. Ingole; A. Schwartzman; H. Liang Investigation of abrasive wear at the nanometer-length scale is presented on single crystalline (001) and amorphous silicon. Experiments were performed using nanoindentation and nanoscratch approaches. Surface characterization was carried out using an atomic...