The segmented carbon seal is regularly used for sealing bearing chambers of aeronautical turboengines or as part of a buffer seal in space turbopumps. The seal operates with contaminated air or with an inert gas and is made of many identical carbon segments (generally three or six) with reciprocally overlapping ends. The segments are pressed against the rotor by the pressure difference between the upstream and the downstream chambers and by a circumferential (garter) spring. The pressure difference and an axial spring press the segments also against the stator. The inner cylindrical surface of each segment is provided with pads that create an aerodynamic lift proportional to the rotor speed. Following this lift force, the segments of the seal are pushed away from the rotor and the seal opens. The contact between the rotor and the segments is lost, and an axial leakage path is thus created. Although it was developed since long, a model for calculating the characteristics of the segmented seal is completely absent from the scientific literature. The goal of the present work is to fill this gap at least for the static characteristics (leakage and torque). The analysis is carried out for a single segment of the seal by supposing that all the segments have the same characteristics. Each segment has a planar motion (i.e., three degrees-of-freedom (3DOF)), and therefore the film thickness under each pad is not uniform. Given the stationary operating conditions (pressure difference and rotation speed), the present model calculates the equilibrium position of each segment on the bases of the lift and the friction force acting on the pads, the friction forces acting on the nose of the seal, and the radial and axial springs. Once found the static equilibrium position, the leakage and the torque of the seal are calculated. A parametric study enlightens the importance of the pad waviness, the pocket depth, and the spring forces on the characteristics of the segmented seal.

References

1.
Oike
,
M.
,
Nosaka
,
M.
,
Watanabe
,
Y.
,
Kikuchi
,
M.
, and
Kamijo
,
K.
,
1988
, “
Experimental Study on High-Pressure Gas Seals for a Liquid Oxygen Turbopump
,”
STLE Trans.
,
31
(
1
), pp.
91
97
.
2.
Oike
,
M.
,
Nosaka
,
M.
,
Kikuchi
,
M.
,
Watanabe
,
Y.
, and
Kamijo
,
K.
,
1990
, “
Study on a Carbon Segmented Circumferential Seal for a Liquid Oxygen Turbopump
,”
Japan International Tribology Conference
, Nagoya, Japan, Oct. 29–Nov. 1, pp.
283
288
.
3.
Nosaka
,
M.
, and
Oike
,
M.
,
1990
, “
Shaft Seals of Turbopumps for Rockets
,”
Jpn. J. Tribol.
,
35
(
4
), pp.
411
421
.
4.
Oike
,
M.
,
Nosaka
,
M.
,
Kikuchi
,
M.
, and
Watanabe
,
Y.
,
1992
, “
Performance of a Segmented Circumferential Seal for a Liquid Oxygen Turbopump (Part 1): Sealing Performance
,”
Jpn. J. Tribol.
,
37
(
4
), pp.
511
523
.
5.
Oike
,
M.
,
Nagao
,
R.
,
Nosaka
,
M.
,
Kamijo
,
K.
, and
Jinnouchi
,
T.
,
1995
, “
Characteristics of a Shaft Seal System for the LE-7 Liquid Oxygen Turbopump
,”
AIAA
Paper No. 95-3102.
6.
Burcham
,
R. E.
,
1978
, “
Liquid Rocket Engine Turbopump Rotating-Shaft Seal
,” Report No.
NASA S-8121
.
7.
Burcham
,
R. E.
,
1983
, “
High-Speed Cryogenic Self-Acting, Shaft Seals for Liquid Rocket Turbopumps
,” Report No.
NASA CR-168194
.
8.
Solidworks, 2017, “Solidworks Flow Simulation,” DASSAULT SYSTEMES, Vélizy-Villacoublay, France, accessed Jan. 12,
2017
, http://www.solidworks.fr/sw/products/simulation/flow-simulation.htm
9.
Arghir
,
M.
,
Le Lez
,
S.
, and
Frêne
,
J.
,
2006
, “
Finite Volume Solution of the Compressible Reynolds Equation—Linear and Non Linear Analysis of Gas Bearings
,”
Proc. Inst. Mech. Eng., Part J
,
220
(
7
), pp.
617
627
.
10.
Constantinescu
,
V. N.
,
1969
,
Gas Lubrication
,
ASME, United Engineering Center
,
New York
.
11.
Crolet
,
A.
,
2008
, “
Contribution à l'étude de l'influence du Comportement Vibratoire du Système ‘Pièce-Outil-Machine’ sur la Qualité de Surface Obtenue en Tournage de Superfinition
,” Thèse de Doctorat de l'Université de l'Institut Polytechnique de Lorraine, Nancy, France.
12.
Johnson
,
K. L.
,
1985
,
Contact Mechanics
,
Cambridge University Press
,
Cambridge, UK
.
13.
Greenwood
,
J. A.
, and
Williamson
,
J. B. P.
,
1966
, “
Contact of Nominally Flat Surfaces
,”
Proc. R. Soc. London A
,
295
(
1442
), pp.
300
319
.
14.
Lebeck
,
A. O.
,
1991
,
Principles and Design of Mechanical Face Seals
,
John Wiley & Sons, Inc.
, Hoboken, NJ.
15.
Kalker
,
J. J.
,
Dekking
,
F. M.
, and
Vollebregt
,
E. A. H.
,
1997
, “
Simulation of Rough, Elastic Contacts
,”
ASME J. Appl. Mech.
,
64
(
2
), pp.
361
368
.
16.
van Ostayen
,
R. A. J.
,
van Beek
,
A.
, and
Ros
,
M.
,
2004
, “
A Mathematical Model of the Hydro-Support: An Elasto-Hydrostatic Thrust Bearing With Mixed Lubrication
,”
Tribol. Int.
,
37
(
8
), pp.
607
616
.
17.
IMSL Fortran Numerical Library, 2017, “Embeddable Numerical Analysis Functions for Fortran Applications,” Rogue Wave Software, Inc., Louisville, CO, accessed Jan. 12,
2017
, http://www.roguewave.com/products-services/imsl-numerical-libraries/fortran-libraries
You do not currently have access to this content.