The tribological properties of Fe–Cr–B alloys were studied sliding against SiC ball in liquid paraffin oil. The boron played an important role in improving tribological properties of alloys. The friction coefficients of alloys decreased with the increase of normal load and sliding speed. The Fe–Cr–B alloys showed better wear resistance than that of Fe–Cr alloy. Fe-21 wt.% Cr-7 wt.% B alloy had the best tribological properties. The wear mechanism of Fe–Cr alloy was abrasive wear and plastic deformation. The wear mechanism of Fe–Cr–B alloys was microploughing and fatigue flaking pits.
Issue Section:
Friction & Wear
References
1.
Alman
, D. E.
, Hawk
, J. A.
, Tylczak
, J. H.
, Dŏgan
, C. P.
, and Wilson
, R. D.
, 2001
, “Wear of Iron–Aluminide Intermetallic-Based Alloys and Composites by Hard Particles
,” Wear
, 251
(1–2
), pp. 875
–884
.10.1016/S0043-1648(01)00745-12.
Khvan
, A. V.
, Hallstedt
, B.
, and Broeckmann
, C.
, 2014
, “A Thermodynamic Evaluation of the Fe-Cr-C System
,” Calphad
, 46
(3), pp. 24
–33
.10.1016/j.calphad.2014.01.0023.
Yüksel
, N.
, and Sahin
, S.
, 2014
, “Wear Behavior–Hardness–Microstructure Relation of Fe-Cr-C and Fe-Cr-C-B Based Hardfacing Alloys
,” Mater. Des.
, 58
, pp. 491
–498
.10.1016/j.matdes.2014.02.0324.
Veinthal
, R.
, Sergejev
, F.
, Zikin
, A.
, Tarbe
, R.
, and Hornung
, J.
, 2013
, “Abrasive Impact Wear and Surface Fatigue Wear Behaviour of Fe-Cr-C PTA Overlays
,” Wear
, 301
(1–2
), pp. 102
–108
.10.1016/j.wear.2013.01.0775.
Wang
, Y. Y.
, Yue
, W.
, She
, D. S.
, Fu
, Z. Q.
, Huang
, H. P.
, and Liu
, J. J.
, 2014
, “Effects of Surface Nanocrystallization on Tribological Properties of 316L Stainless Steel Under MoDTC/ZDDP Lubrications
,” Tribol. Int.
, 79
, pp. 42
–51
.10.1016/j.triboint.2014.05.0216.
Ma
, G. Z.
, Xu
, B. S.
, Wang
, H. D.
, Si
, H. J.
, and Yang
, D. X.
, 2011
, “Effect of Surface Nanocrystallization on the Tribological Properties of 1Cr18Ni9Ti Stainless Steel
,” Mater. Lett.
, 65
(9
), pp. 1268
–1271
.10.1016/j.matlet.2011.01.0417.
Lv
, X. R.
, Wang
, S. G.
, Liu
, Y.
, Long
, K.
, Li
, S.
, and Zhang
, Z. D.
, 2008
, “Effect of Nanocrystallization on Tribological Behaviors of Ingot Iron
,” Wear
, 264
(7–8
), pp. 535
–541
.10.1016/j.wear.2007.04.0108.
Mao
, X. Y.
, Li
, D. Y.
, Fang
, F.
, Tan
, R. S.
, and Jiang
, J. Q.
, 2011
, “Application of a Simple Surface Nanocrystallization Process to a Cu–30Ni Alloy for Enhanced Resistances to Wear and Corrosive Wear
,” Wear
, 271
(9–10
), pp. 1224
–1230
.10.1016/j.wear.2010.12.0639.
Fu
, L. C.
, Yang
, J.
, Bi
, Q. L.
, Zhu
, S. Y.
, and Liu
, W. M.
, 2009
, “Dry-Sliding Tribological Properties of Nano-Eutectic Fe83B17 Alloy
,” Tribol. Lett.
, 34
(3
), pp. 185
–191
.10.1007/s11249-009-9422-x10.
Wang
, L.
, Ma
, J. Q.
, Yang
, J.
, Bi
, Q. L.
, Fu
, L. C.
, and Liu
, W. M.
, 2010
, “Dry-Sliding Tribological Properties of a Nano-Eutectic Fe1.87C0.13 Alloy
,” Wear
, 268
(7–8
), pp. 991
–995
.10.1016/j.wear.2009.12.02811.
Hosseini
, N.
, Karimzadeh
, F.
, Abbasi
, M. H.
, and Enayati
, M. H.
, 2012
, “A Comparative Study on the Wear Properties of Coarse-Grained Al6061 Alloy and Nanostructured Al6061-Al2O3 Composites
,” Tribol. Int.
, 54
, pp. 58
–67
.10.1016/j.triboint.2012.04.02012.
Stempflé
, P.
, Pollet
, F.
, and Carpentier
, L.
, 2008
, “Influence of Intergranular Metallic Nanoparticles on the Fretting Wear Mechanisms of Fe-Cr-Al2O3 Nanocomposites Rubbing on Ti-6Al-4V
,” Tribol. Int.
, 41
(11
), pp. 1009
–1019
.10.1016/j.triboint.2008.02.01913.
Jha
, N.
, Badkul
, A.
, Mondal
, D. P.
, Das
, S.
, and Singh
, M.
, 2011
, “Sliding Wear Behavior of Aluminum Syntactic Foam: A Comparison With Al-10 wt% SiC Composites
,” Tribol. Int.
, 44
(3
), pp. 220
–231
.10.1016/j.triboint.2010.10.00414.
Liu
, F.
, Yi
, G. W.
, Wang
, W. Z.
, Shan
, Y.
, and Jia
, J. H.
, 2013
, “Tribological Properties of NiCr-Al2O3 Cermet-Based Composites With Addition of Multiple-Lubricants at Elevated Temperatures
,” Tribol. Int.
, 67
, pp. 164
–173
.10.1016/j.triboint.2013.07.01715.
Cui
, G. J.
, Bi
, Q. L.
, Niu
, M. Y.
, Yang
, J.
, and Liu
, W. M.
, 2013
, “The Tribological Properties of Bronze-SiC-Graphite Composites Under Sea Water Condition
,” Tribol. Int.
, 60
, pp. 25
–35
.10.1016/j.triboint.2012.11.00516.
Wang
, X. H.
, Zou
, Z. D.
, Qu
, S. Y.
, and Song
, S. L.
, 2005
, “Microstructure and Wear Properties of Fe-Based Hardfacing Coating Reinforced by TiC Particles
,” J. Mater. Process. Technol.
, 168
(1
), pp. 89
–94
.10.1016/j.jmatprotec.2004.11.00117.
Srivastava
, A. K.
, and Das
, K.
, 2010
, “The Abrasive Wear Resistance of TIC and (Ti,W)C-Reinforced Fe-17Mn Austenitic Steel Matrix Composites
,” Tribol. Int.
, 43
, pp. 944
–950
.10.1016/j.triboint.2009.12.05718.
Prabhu
, T. R.
, Varma
, V. K.
, and Vedantam
, S.
, 2014
, “Effect of SiC Volume Fraction and Size on Dry Sliding Wear of Fe/SiC/Graphite Hybrid Composites for High Sliding Speed Applications
,” Wear
, 309
(1–2
), pp. 1
–10
.10.1016/j.wear.2013.10.00619.
Cui
, G. J.
, and Kou
, Z. M.
, 2014
, “The Effect of Boron on Mechanical Behavior and Microstructure for Fe-Cr Matrix Alloy Prepared by P/M
,” J. Alloys Compd.
, 586
, pp. 699
–702
.10.1016/j.jallcom.2013.10.11020.
Kim
, H. J.
, Yoon
, B. H.
, and Lee
, C. H.
, 2001
, “Wear Performance of the Fe-Based Alloy Coatings Produced by Plasma Transferred Arc Weld-Surfacing Process
,” Wear
, 249
(10–11
), pp. 846
–852
.10.1016/S0043-1648(01)00683-421.
Meric
, C.
, Sahin
, S.
, Backir
, B.
, and Koksal
, N. S.
, 2006
, “Investigation of the Boronizing Effect on the Abrasive Wear Behavior in Cast Irons
,” Mater. Des.
, 27
(9
), pp. 751
–757
.10.1016/j.matdes.2005.01.01822.
Zhang
, J. Y.
, Liu
, W. M.
, and Xue
, Q. J.
, 1999
, “The Friction and Wear Behaviors of S-[2-S-(2-hydroxylpropyl)benthiazole]dioctyldithiocarbamic Acid Ester as Additive in Liquid Paraffin
,” Wear
, 224
(1
), pp. 50
–55
.10.1016/S0043-1648(98)00331-723.
Xia
, Y. Q.
, Liu
, W. M.
, and Xue
, Q. J.
, 2002
, “Friction and Wear Behavior of Nodular Cast Iron Modified by a Laser Micro-Precision Treatment Sliding Against Steel Under the Lubrication of Liquid Paraffin Containing Various Additives
,” Wear
, 253
(7–8
), pp. 752
–758
.10.1016/S0043-1648(02)00150-324.
Cheng
, J.
, Yang
, J.
, Ma
, J.
, Bi
, Q.
, Zhang
, X.
, Fu
, L.
, Li
, F.
, Zhu
, S.
, and Liu
, W.
, 2012
, “The Tribological Behavior of a Ti-46Al-2Cr-2Nb Alloy Under Liquid Paraffin Lubrication
,” Tribol. Lett.
, 46
(3
), pp. 233
–241
.10.1007/s11249-012-9942-725.
Wang
, L.
, Yang
, J.
, Bi
, Q. L.
, Ma
, J. Q.
, Fu
, L. C.
, and Liu
, W. M.
, 2010
, “The Tribological Properties of a Nano-Eutectic Fe1.87C0.13 Alloy Under Liquid Paraffin Lubrication
,” Tribol. Lett.
, 37
(2
), pp. 183
–189
.10.1007/s11249-009-9513-826.
Hamrock
, B. J.
, and Dowson
, D.
, 1977
, “Isothermal Elastohydrodynamic Lubrication of Point Contacts: Part III-Fully Flooded Results
,” ASME J. Tribol.
, 99
(2
), pp. 264
–276
.10.1115/1.345307427.
Ma
, W. L.
, and Lu
, J. J.
, 2011
, “Effect of Sliding Speed on Surface Modification and Tribological Behavior of Copper-Graphite Composite
,” Tribol. Lett.
, 41
(2
), pp. 363
–370
.10.1007/s11249-010-9718-x28.
Archard
, J. F.
, 1953
, “Contact and Rubbing of Flat Surfaces
,” J. Appl. Phys.
, 24
(8
), pp. 981
–988
.10.1063/1.172144829.
Yang
, J.
, Ma
, J. Q.
, Bi
, Q. L.
, Liu
, W. M.
, and Xue
, Q. J.
, 2008
, “Tribological Properties of Fe3Al Material Under Water Environment
,” Mater. Sci. Eng., A
, 490
(1–2
), pp. 90
–94
.10.1016/j.msea.2008.01.02430.
Uekawa
, N.
, and Kaneko
, K.
, 1996
, “Dopant Reduction in p-Type Oxide Films Upon Oxygen Absorption
,” J. Phys. Chem.
, 100
(10
), pp. 4193
–4198
.10.1021/jp952784m31.
Li
, Y.
, Ruoff
, R. S.
, and Chang
, R. P. H.
, 2003
, “Boric Acid Nanotubes, Nanotips, Nanorods, Microtubes, and Microtips
,” Chem. Mater.
, 15
(17
), pp. 3276
–3285
.10.1021/cm030261i32.
Ma
, J. Q.
, Li
, F.
, Cheng
, J.
, Fu
, L. C.
, Qiao
, Z. H.
, Liu
, W. M.
, and Yang
, J.
, 2013
, “Tribological Behavior of Ti3AlC2 Against SiC at Ambient and Elevated Temperatures
,” Tribol. Lett.
, 50
(3
), pp. 323
–330
.10.1007/s11249-013-0126-xCopyright © 2015 by ASME
You do not currently have access to this content.
