The aim of this study is to design the shapes of the surfaces of sliders to meet the load demands specified by the designers. A direct problem solver is built to provide solutions for pressure distribution between the slider and the rotor for various geometric conditions and load demands. The direct problem solver is then incorporated with the conjugate gradient method so as to develop an inverse method for the slider surface shape design. The specified load demands considered in this study are categorized into two kinds: (1) specified pressure distribution within the fluid film and (2) specified resultant forces plus specified centers of load. Several cases at various bearing numbers are tested to demonstrate the validity of the inverse shape design approach. Results show that the surface shape of a slider can be designed efficiently to comply with the specified load demands considered in the present study by using the inverse method.

Issue Section:
Technical Papers
Keywords:
magnetic bearings, machine bearings, lubrication, inverse problems, optimisation, rotors, conjugate gradient methods, Slider, Shape Design, Inverse Method, Conjugate Gradient Method
Topics:
Bearings, Fluid films, Gradient methods, Optimization, Pressure, Shape design, Shapes, Stress, Design
1.
White
,
J. W.
,
1983
, “
Flying Chrarcteristics of the ‘Zero-Load’ Slider Bearing
,”
ASME J. Lubr. Technol.
,
105
, pp.
484
–
490
.
2.
Buckholz
,
R. H.
,
1986
, “
Effects of Power-Law, Non-Newtonian Lubricants on Load Capacity and Friction for Plane Slider Bearings
,”
ASME J. Tribol.
,
108
, pp.
86
–
91
.
3.
Kubo
,
M.
,
Ohtsubo
,
Y.
,
Kawashima
,
N.
, and
Marumo
,
H.
,
1988
, “
Finite Element Solution for the Rarefied Gas Lubrication Problem
,”
ASME J. Tribol.
,
110
, pp.
335
–
341
.
4.
Hu
,
Y.
, and
Bogy
,
D. B.
,
1997
, “
Dynamic Stability and Spacing Modulation of Sub-25 nm Fly Height Sliders
,”
ASME J. Tribol.
,
119
, pp.
646
–
652
.
5.
Wang
,
N.
,
Ho
,
C. L.
, and
Cha
,
K. C.
,
2000
, “
Engineering Optimum Design of Fluid-Film Lubricated Bearings
,”
Tribol. Trans.
,
43
, pp.
377
–
386
.
6.
Hu
,
Y.
,
1999
, “
Contact Take-Off Characteristics of Proximity Recording Air Bearing Sliders in Magnetic Hard Disk Drivers
,”
ASME J. Tribol.
,
121
, pp.
948
–
954
.
7.
Hashimoto
,
H.
, and
Hattori
,
Y.
,
2000
, “
Improvement of the Static and Dynamic Characteristics of Magnetic Head Sliders by Optimum Design
,”
ASME J. Tribol.
,
122
, pp.
280
–
287
.
8.
Yoon
,
S. J.
, and
Choi
,
D. H.
,
1997
, “
An Optimum Design of the Transverse Pressure Contour Slider for Enhanced Flying Characteristics
,”
ASME J. Tribol.
,
119
, pp.
520
–
524
.
9.
Kotera
,
H.
, and
Shima
,
S.
,
2000
, “
Shape Optimization to Perform Prescribed Air Lubrication Using Genetic Algorithm
,”
Tribol. Trans.
,
43
, pp.
837
–
841
.
10.
El-Gamal
,
H. A.
, and
Awad
,
T. H.
,
1994
, “
Optimum Model Shape of Sliding Bearings for Oscillating Motion
,”
Tribol. Int.
,
27
, pp.
189
–
196
.
11.
O’Hara
,
M. A.
,
Hu
,
Y.
, and
Bogy
,
D. B.
,
2000
, “
Optimization of Proximity Recording Air Bearing Sliders in Magnetic Hard Disk Drivers
,”
ASME J. Tribol.
,
122
, pp.
257
–
259
.
12.
Kang
,
T. S.
,
Choi
,
D. H.
, and
Jeong
,
T. G.
,
2001
, “
Optimal Design of HDD Air-Lubricated Slider Bearings for Improving Dynamic Characteristics and Operating Performance
,”
ASME J. Tribol.
,
123
, pp.
541
–
547
.
13.
Hanke, M., 1995, Conjugate Gradient Type Methods for Ill-Posed Problems, John Wiley & Sons, New York.
14.
Cheng
,
C. H.
, and
Wu
,
C. Y.
,
2000
, “
An Approach Combining Body-Fitted Grid Generation and Conjugate Gradient Methods for Shape Design in Heat Conduction Problems
,”
Numer. Heat Transfer, Part B
,
37
, pp.
69
–
83
.
15.
Cheng
,
C. H.
, and
Chang
,
M. H.
,
2003
, “
Shape Design for a Cylinder With Uniform Temperature Distribution on the Outer Surface by Inverse Heat Transfer Method
,”
Int. J. Heat Mass Transfer
,
46
, pp.
101
–
111
.
16.
Cheng
,
C. H.
, and
Chang
,
M. H.
,
2003
, “
Shape Identification by Inverse Heat Transfer Method
,”
ASME J. Heat Transfer
,
125
, pp.
224
–
231
.
17.
Gross, W. A., Matsch, L. A., Castelli, V., Eshel, A., Vohr, J. H., and Wildmann, M., 1980, Fluid Film Lubrication, John Wiley & Sons, New York.
Copyright © 2004
 by ASME
You do not currently have access to this content.