This paper describes the use of a recently developed high temperature impulse-frequency response apparatus to directly measure dynamic modulus and internal damping of high temperature composite materials, matrix materials, and reinforcing fibers as a function of temperature. An extensional vibration test was used for determination of the complex Young’s modulus of fiber specimens as a function of temperature. A flexural vibration test was used for determination of the complex flexural modulus of matrix and unidirectional composite specimens (0 and 90 deg fiber orientations) as a function of temperature. These results were obtained from tests done on two different fiber reinforced composite materials: boron/epoxy (B/E) and Silicon Carbide/Ti-6Al-4V (SiC/Ti). The results from these tests were then used to assess the validity of micromechanics predictions of composite properties at elevated temperatures. Micromechanics predictions of composite moduli and damping at elevated temperatures show good agreement with measured values for the 0 deg case (longitudinal) but only fair agreement for the 90 deg case (transverse). In both cases, the predictions indicate the correct trends in the properties.

Issue Section:
Technical Papers
Topics:
Composite materials, Temperature, Testing, Fibers, Damping, High temperature, Micromechanics (Engineering), Vibration tests, Boron, Epoxy adhesives, Epoxy resins, Fiber reinforced composites, Impulse (Physics), Silicon, Young's modulus
1.
Jinen
 
E.
,
1988
, “
Temperature Dependence of Dynamic Properties of Phenolic-Fiber-Reinforced Thermo Plastic
,”
Composites Science and Technology
, Vol.
33
, pp.
19
–
33
.
2.
Jones
 
D. I. G.
,
1974
, “
Temperature-Frequency Dependence of Dynamic Properties of Damping Materials
,”
Journal of Sound and Vibration
, Vol.
33
, No.
4
, pp.
451
–
470
.
3.
Jones
 
D. I. G.
,
1978
, “
A Reduced-Temperature Monogram for characterization of Damping Material Behavior
,”
Shock and Vibration, Bulletin
, Vol.
48
, No.
2
, pp.
13
–
22
.
4.
Jones, R. M., 1975, Mechanics of Composite Materials, Hemisphere Pub. Co.
5.
Kawabata, S., 1989, “Measurements of Anisotropic Mechanical Property and Thermal Conductivity of Single Fiber for Several High Performance Fibers,” Proc. 4th Japan—U.S. Conference on Composite Materials, Technomic Pub. Co., Lancaster, PA, pp. 253–262.
6.
Kolsky, H., 1963, Stress Waves in Solids, Dover Publication, New York.
7.
Lee
 
C. Y.
,
Thompson
 
B. S.
,
Gandhi
 
M. V.
,
1988
, “
Temperature Dependent Dynamic Mechanical Properties of Polymeric Laminated Beams
,”
ASME JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY
, Vol.
110
, No.
2
, pp.
174
–
179
.
8.
Lesieutre, G. A., Eckel, A. J., and DiCarlo, J. A., 1989, “Increased Graphite Fiber Damping Via Intercalation,” Paper No. GDA, Proc. DAMPING 89 Conference, West Palm Beach, FL, WRDC-TR-89-3116.
9.
Pant, R. H., 1992, “Analysis and Testing of Dynamic Micromechanical Behavior of Composite Materials at Elevated Temperatures,” M.S. thesis, Wayne State University.
10.
Springer, G. S., 1984, Environmental Effects on Composite Materials, Technomic, 1981, Vol. II.
11.
Suarez, S. A., Gibson, R. F., Sun, C. T., and Chaturvedi, S. K., 1986, “The Influence of Fiber Length and Fiber Orientation on Damping and Stiffness of Polymer Composite Materials,” Vol. 26, No. 2, pp. 175–184.
12.
Suarez
 
S. A.
, and
Gibson
 
R. F.
,
1987
, “
Improved Impulse-Frequency Response Techniques for Measurements of Dynamic Mechanical Properties of Composite Materials
,”
Journal of Testing and Evaluation
, Vol.
15
, No.
2
, pp.
114
–
121
.
13.
Takayanagi, M., 1965, in Proc. Fourth International Congress on Rheology, Part I, Interscience Publisher, New York.
14.
Thirumalai, R., 1992, “Development of an Apparatus to Measure Dynamic Modulus and Damping of Composite Materials and their Constituents at Elevated Temperatures,” M.S. thesis, Wayne State University.
15.
Thirumalai, R., and Gibson, R. F., 1993, “Characterization of Dynamic Exten-sional Modulus and Damping of Reinforcing Fibers for Advanced Composites at Elevated Temperatures,” Damping of Multiphase Inorganic Materials, ASM International, Materials Park, Ohio, pp. 37–46.
16.
Ward, I. M., 1985, Mechanical Properties of Solid Polymers, Second Edition, Wiley.
This content is only available via PDF.
Copyright © 1996
 by The American Society of Mechanical Engineers
You do not currently have access to this content.