Machining of advanced materials, such as composite, encounters high cutting temperatures and rapid tool wear because of the abrasive nature of the reinforcement phases in the workpiece materials. Ultrahard coatings, such as chemical vapor deposition diamond, have been used for machining such advanced materials. Wear of diamond-coated tools is characterized by catastrophic coating failure, plausibly due to the high stress developed at the coating-substrate interface at high temperatures because of very different elastic moduli and thermal expansion coefficients. Temperature reductions, therefore, may delay the onset of the coating failure and offer tool life extension. In this study, a passive heat-dissipation device, the heat pipe, has been incorporated in composite machining. Though it is intuitive that heat transfer enhanced by the heat pipe may reduce tool temperatures, the heat pipe will likely increase heat partitioning into the tool at the rake face, and complicate the temperature reduction effectiveness. A combined experimental, analytical, and numerical approach was used to investigate the heat-pipe effects on cutting tool temperatures. A machining experiment was conducted and the heat-source characteristics were analyzed using cutting mechanics. With the heat sources as input, cutting tool temperatures in machining, without or with a heat pipe, were analyzed using finite element simulations. The simulations encompass a 3-D model of a cutting tool system and a 2-D chip model. The heat flux over the rake-face contact area was used in both models with an unknown heat partition coefficient, determined by matching the average temperature at the tool-chip contact from the two models. Cutting tool temperatures were also measured in machining using thermocouples. The simulation results agree reasonably with the experiment. The model was used to evaluate how the heat pipe modifies the heat transport in a cutting tool system. Applying heat-pipe cooling inevitably increases the heat flux into the tool because of the enhanced heat dissipation. However, the heat pipe is still able to reduce the tool-chip contact temperatures, though not dramatically at current settings. The parametric study using the finite element analysis (FEA) models shows that the cooling efficiency decreases as the cutting speed and feed increase, because of the increased heat flux and heat-source area. In addition, increasing the heat-pipe volume and decreasing the heat-pipe distance to the heat source enhances the heat-pipe cooling effectiveness.
Skip Nav Destination
e-mail: kchou@eng.ua.edu
Article navigation
October 2007
Research Papers
Cutting Tool Temperature Analysis in Heat-Pipe Assisted Composite Machining
Jie Liu,
Jie Liu
Graduate Research Assistant
Mechanical Engineering Department,
The University of Alabama
, Tuscaloosa, AL 35487
Search for other works by this author on:
Y. Kevin Chou
Y. Kevin Chou
Associate Professor
Mechanical Engineering Department,
e-mail: kchou@eng.ua.edu
The University of Alabama
, Tuscaloosa, AL 35487
Search for other works by this author on:
Jie Liu
Graduate Research Assistant
Mechanical Engineering Department,
The University of Alabama
, Tuscaloosa, AL 35487
Y. Kevin Chou
Associate Professor
Mechanical Engineering Department,
The University of Alabama
, Tuscaloosa, AL 35487e-mail: kchou@eng.ua.edu
J. Manuf. Sci. Eng. Oct 2007, 129(5): 902-910 (9 pages)
Published Online: April 8, 2007
Article history
Received:
June 15, 2006
Revised:
April 8, 2007
Citation
Liu, J., and Kevin Chou, Y. (April 8, 2007). "Cutting Tool Temperature Analysis in Heat-Pipe Assisted Composite Machining." ASME. J. Manuf. Sci. Eng. October 2007; 129(5): 902–910. https://doi.org/10.1115/1.2752528
Download citation file:
Get Email Alerts
On-Orbit Processing and Hardware Performance of Microgravity Hydrothermal Synthesis for Graphene Aerogel
J. Manuf. Sci. Eng (December 2024)
A Review on Metallic Drilling Burrs: Geometry, Formation, and Effect on the Mechanical Strength of Metallic Assemblies
J. Manuf. Sci. Eng (April 2025)
Related Articles
On a Novel Tool Life Relation for Precision Cutting Tools
J. Manuf. Sci. Eng (May,2005)
Binderless CBN Tools, a Breakthrough for Machining Titanium Alloys
J. Manuf. Sci. Eng (May,2005)
A Geometrical Simulation System of Ball End Finish Milling Process and Its Application for the Prediction of Surface Micro Features
J. Manuf. Sci. Eng (February,2006)
The Experimental and Theoretical Evaluation of an Indirect Cooling System for Machining
J. Heat Transfer (March,2011)
Related Chapters
Cutting Performance and Wear Mechanism of Cutting Tool in Milling of High Strength Steel 34CrNiMo6
Proceedings of the 2010 International Conference on Mechanical, Industrial, and Manufacturing Technologies (MIMT 2010)
Effectiveness of Minimum Quantity Lubrication (MQL) for Different Work Materials When Turning by Uncoated Carbide (SNMM and SNMG) Inserts
Proceedings of the 2010 International Conference on Mechanical, Industrial, and Manufacturing Technologies (MIMT 2010)
Cutting Tool Wear Monitoring Applying Support Vector Machines and Genetic Algorithms
International Conference on Advanced Computer Theory and Engineering (ICACTE 2009)