A review of recent developments related to the use of dimethyl ether (DME) in engines is presented. Research work discussed is in the areas of engine performance and emissions, fuel injection systems, spray and ignition delay, and detailed chemical kinetic modeling. DME’s properties and safety aspects are discussed. A simplified theoretical explanation of the emissions behavior of DME is presented. A discussion is presented proposing DME as a significant factor in the future international energy picture. Due to its beneficial combustion properties, possibility of production from a variety of sources, and usefulness as a chemical feed stock, DME can be used in a variety of applications in addition to transportation.

Issue Section:
Internal Combustion Engines
Keywords:
internal combustion engines, air pollution control, emission, natural gas technology, combustion, ignition
Topics:
Combustion, Diesel, Diesel engines, Emissions, Engines, Ethers (Class of compounds), Fuels, Sprays, Soot
1.
Brook, D. L., Rallis, C. J., Lane, N. W., and Dipolat, C., 1984, “Methanol with Dimethyl Ether Ignition Promoter as Fuel for Compression Ignition Engines,” Proceedings of the 19th Intersociety Energy Conversion Engineering Conference, pp. 654–658.
2.
Murayama, T., Chikahisa, J., Guo, J., and Miyano, M., 1992, “A Study of Compressions Ignition Methanol Engine With Converted Dimethyl Ether as an Ignition Improver,” SAE Paper 922212.
3.
Cipolat, D., Jawurek, H. H., and Rallis, C. J., 1991, “Methanol/Diethyl Ether Fuelling of a Compression Ignition Engine,” Proceedings of the IX International Symposium on Alcohol Fuels, pp. 411–415.
4.
Guo, J., Chikashisa, T., and Murayama, T., 1994, “Improvement of Performance and Emissions of a Compression Ignition Methanol Engine with Dimethyl Ether,” SAE Paper 941908.
5.
Sorenson, S. C., and Mikkelsen, S. E., 1995, “Performance and Emissions of a 0.273 Liter Direct Injection Diesel Engine Fueled With Neat Dimethyl Ether,” SAE Paper 950964.
6.
Hansen, J. B., Voss, B., Joensen, F., Sigurdardo´ttir, I.-D., 1995, “Large Scale Manufacture of Dimethyl Ether—A New Alternative Diesel Fuel From Natural Gas,” SAE Paper No. 950063.
7.
Fleisch, T., McCarthy, C., Basu, A., Udovich, Charbonneau, P., Slodowske, W., Mikkelsen, S.-E., and McCandless, J., 1995, “A New Clean Diesel Technology: Demonstration of ULEV Emissions on a Navistar Diesel Engine Fueled With Dimethyl Ether,” SAE Paper 950061.
8.
Kapus, P., and Ofner, H., 1995, “Development of Fuel Injection Equipment and Combustion System for DI Diesels Operated on Dimethyl Ether,” SAE Paper 950062.
9.
Ofner, H., Gill, D. W., and Kammerdiener, T., 1996, “A Fuel Injection Concept for Dimethyl Ether,” Application of Powertrain and Fuel Technologies to Meet Emissions Standards, ASME, New York, p. 289.
10.
Sorenson, S. C., Glensvig, M., and Abata, D. L., 1998, “Dimethyl Ether in Diesel Fuel Injection Systems,” SAE Paper 981159.
11.
Christensen, R., Sorenson, S. C., Jensen, M. G., and Hansen, K. F., 1998, “Engine Operation on Dimethyl Ether in a Naturally Aspirated, DI Diesel Engine,” SAE Paper 971665.
12.
Glensvig, M., Sorenson, S. C., and Abata, D. L., 1996, “High Pressure Injection of DME,” Alternative Fuels, Vol. 27-3, ASME, New York, p. 57.
13.
Glensvig, M., Sorenson, S. C., and Abata, D. L., 1997, “An Investigation of the Injection Characteristics of Dimethyl Ether,” Engine Combustion, Performance and Emissions, ICE-Vol. 29-3, ASME, New York, p. 77.
14.
McCandless, J., Teng, H., and Schneyer, J. B., 2000, “Development of a Variable-Displacement, Rail-Pressure Supply Pump for Dimethyl Ether,” SAE Paper 2000-01-0687.
15.
Nielsen, K., and Sorenson, S. C., 1999, “Lubricity Additives and Wear With DME in Diesel Injection Pumps,” Emissions, Fuels and Lubricants and HSDI Engines, ICE-Vol. 33-1, ASME, New York, pp. 145–153.
16.
Bowman
,
F. M.
, and
Seinfeld
,
J. H.
,
1995
, “
Atmospheric Chemistry of Alternative Fuels and Reformulated Gasoline Components
,”
Prog. Energy Combust. Sci.
,
21
, pp.
387
–
417
.
17.
Japar
,
S. M.
,
Wallington
,
T. J.
,
Richert
,
J. F. O.
, and
Ball
,
J. C.
,
1990
, “
The Atmospheric Chemistry of Oxygenated Fuel Additives: t-butyl Alcohol, Dimethyl Ether, and Methyl t-butyl Ether
,”
Int. J. Chem. Kinet.
,
22
, pp.
1257
–
1269
.
18.
Mikkelsen, S.-E., Hansen, J. B., and Sorenson, S. C., 1996, “Dimethyl Ether as an Alternate Fuel for Diesel Engines,” Application of Powertrain and Fuel Technologies to Meet Emissions Standards, ASME, New York, p. 289.
19.
Konno, M., Kajitani, S., Oguma, M., Iwase, T., and Shima, K., 1999, “NO Emission Characteristics of a CI Engine Fueled With Neat Dimethyl Ether,” SAE Paper 1999-01-1116.
20.
Fleisch, T. H., and Meurer, P. C., 1995, “DME: The Diesel Fuel for the 21st Century?” presented at the AVL Conference “Engine and Environment 1995,” Graz, Austria.
21.
Kapus, P., and Cartellieri, W., 1995, “ULEV Potential of a DI/TCI Diesel Passenger Car Engine Operated on Dimethyl Ether,” SAE Paper 952754.
22.
McCandless, J. C., and Li, S., 1997, “Development of a Novel Fuel Injection System (NFIS) for Dimethyl Ether,” SAE Paper 970220.
23.
Bek, B. H., Michalek, D. J., Abata, D. L., and Sorenson, S. C., 1999, “The Onset of Cavitation During Injection of Low Viscosity High Vapor Pressure Fuels,” Engine Design, Controls and DI Sprays, ICE-Vol. 33-2, ASME, New York, pp. 85–91.
24.
Sorenson, S. C., Bek, B. H., Glensvig, M., and Abata, D. L., 1998, “Dimethyl Ether Injection Studies,” Proceedings of the Second International Workshop on Advanced Spray Combustion, Hiroshima, Japan, Nov. 25.
25.
Wakai, K., Nishida, K., Yoshizaki, T., and Hiroyasu, H., 1998, “Spray and Ignition Characteristics of Dimethyl Ether Injected by a D. I. Diesel Injector,” The Fourth International Symposium COMODIA 98, JSME, Japan, pp. 537–542.
26.
Wakai, K., Yoshizaki, T., Nishida, K., Hiroyasu, H., and Kawaguchi, Y., 1999, “Numerical and Experimental Analyses on the Injection Characteristics of Dimethyl Ether With a D. I. Diesel Injection System,” SAE Paper 1999-01-1122.
27.
Wakai, K., Nishida, K., Yoshizaki, T., and Hiroyasu, H., 1999, “Ignition Delays of DME and Diesel Fuel Sprays Injected by a D. I. Diesel Injector,” SAE Paper 1999-01-3600.
28.
Xu, M., Nishida, K., and Hiroyasu, H., 1992, “A Practical Calculation Method for Injection Pressure and Spray Penetration in Diesel Engines,” SAE Paper 960642.
29.
Dec, J. E., and Canaan, R. E., 1998, “PLIF Imaging of NO Formation in a DI Diesel Engine,” SAE Paper 980147.
30.
Edgar, B. L., Dibble, R. W., and Naegeli, D. W., 1997, “Autoignition of Dimethyl Ether and Dimethoxy Methane Sprays at High Pressures,” SAE Paper 971677.
31.
Flynn, P., Mizusawa, M., Uyehara, O. A., and Myers, P. S., 1972, “An Experimental Determination of the Instantaneous Potential Radiant Heat Transfer Within an Operating Diesel Engine,” SAE Transactions, Paper 720022.
32.
Curran
,
H. J.
,
Pitz
,
W. J.
,
Westbrook
,
C. K.
,
Augaut
,
P.
,
Boettner
,
J. C.
, and
Cathonnet
,
M.
,
1998
, “
A Wide Range Modeling Study of Dimethyl Ether
,”
Int. J. Chem. Kinet.
,
30
, pp.
229
–
241
.
33.
Alzueta
,
M.
,
Moro
,
U. J.
,
Bilbao
,
R.
, and
Glarborg
,
P.
,
1999
, “
Oxidation of Dimethyl Ether and Its Interaction With Nitrogen Oxides
,”
Isr. J. Chem.
,
39
, pp.
73
–
86
.
34.
Ofner, H., Gill, D. W., and Krotscheck, C., 1998, “Dimethyl Ether as Fuel for CI Engines—A New Technology and Its Environmental Potential,” SEA Paper 981158.
35.
Verbeek, R., and Van der Weide, J., 1997, “Global Assessment of Dimethyl-Ether: Comparison With Other Fuels,” SAE Paper 971607.
36.
Bek, B. H., and Sorenson, S. C., 1997, “A Mixing Based Model for DME Combustion in Diesel Engines,” Gas Engines and Alternative Fuels, ICE-Vol. 31-3, ASME, New York, p. 97.
37.
Nordin, N., Golovitchev, V. I., and Chomiak, C., 1998, “Computer Evaluation of DI Diesel Engine Fueled With Neat Dimethyl Ether,” presented at the 22nd CIMAC Conference, Copenhagen, May 18–21.
38.
Beatrice, C., Bertoli, C., Del Giacomo, N., and Lazzaro, M., 1996, “An Experimental Characterization of the Formation of Pollutants in DI Diesel Engines Burning Oxygenated Synthetic Fuels,” Application of Powertrain and Fuel Technologies to Meet Emissions Standards, IMechE, London, p. 261.
39.
Cheng, A. S., and Dibble, R. W., 1999, “Emissions Performance of Oxygenate-in-Diesel Blends and Fisher-Tropsch Diesel in a Compression Ignition Engine,” SAE Paper 1999-01-3606.
40.
Miyamoto, N., Ogawa, H., Nurun, N. M., Obata, K., and Arima, T., 1998, “Smokeless, Low NOx High Thermal Efficiency, and Low Noise Diesel Combustion With Oxygenated Agents as Main Fuel,” SAE Paper 980506.
41.
Amann, C. A., Stivender, D. L., Plee, S. L., and MacDonald, J. S., 1980, “Some Rudiments of Diesel Particulate Emissions,” SAE Paper 80251.
42.
Streholw, R. A., 1984, Combustion Fundamentals, McGraw-Hill, New York.
43.
Dec, J. E., 1997, “A Conceptual Model of DI Diesel Combustion Based on Laser-Sheet Imaging,” SAE Paper 970873.
44.
Scholl, K. W., and Sorenson, S. C., 1993, “Combustion of Soybean Oil Methyl Ester in a Direct Injection Diesel Engine,” SAE Transactions, Paper 930934.
45.
Van Doorn, T., ed., 1999, “Dimethyl-ether as Automotive Fuel,” DME Newsletter 3, IEA Newsletter, TNO Automotive.
Copyright © 2001
 by ASME
You do not currently have access to this content.