Research Articles

Effects of the Nonlinear Elastic Behavior of Bicycle Chain on Transmission Efficiency

[+] Author and Article Information
James B. Spicer

Department of Materials Science
and Engineering,
The Johns Hopkins University,
3400 North Charles Street,
Baltimore, MD 21218
e-mail: spicer@jhu.edu

Manuscript received November 30, 2011; final manuscript received August 3, 2012; accepted manuscript posted August 23, 2012; published online January 22, 2013. Assoc. Editor: Wei-Chau Xie.

J. Appl. Mech 80(2), 021005 (Jan 22, 2013) (8 pages) Paper No: JAM-11-1455; doi: 10.1115/1.4007431 History: Received November 30, 2011; Revised August 03, 2012; Accepted August 23, 2012

A model for nonfrictional power loss in derailleur-type, bicycle chain drives is developed to identify factors that influence transmission efficiency. Existing treatments of chain drive efficiency consider frictional losses but these do not explain the measured tension dependence of power losses and efficiencies for derailleur-type systems. Based on a nonlinear, spring-mass, mechanical transmission line, the model developed in this work shows that losses can be related to harmonic generation and dispersion in the chain. The nonlinear response leading to harmonic generation results from elastic contact at pin-bushing interfaces while dispersion is related to the periodic nature of the chain construction. Using this approach, the tension-dependence of power loss and efficiency are modeled and the influences of various chain-related characteristics on efficiency are assessed. If Hertzian contact descriptions are used, then the dependence of loss and efficiency on pin-bushing clearance, contact length and modulus can be estimated. Modeled results agree with experiment and show that power loss decreases with increasing chain tension and that efficiency varies nearly linearly with the reciprocal of the chain tension under operational conditions that are typical for bicycle chain drives. Significant increases to the power transmission efficiency of bicycle chain drives in derailleur-based systems could be achieved by altering the geometries and materials of current chain components.

Copyright © 2013 by ASME
Topics: Chain , Bicycles , Bushings , Tension
Your Session has timed out. Please sign back in to continue.


Keller, J., 1983, “Der Wirkunsgrad im Fahrradantrieb,” Radmarkt, 12, pp. 71–75.
Hollingworth, N. E., and Hills, D. A., 1986, “Forces in a Heavy-Duty Drive Chain During Articulation,” Proc. Inst. Mech. Eng., Part C: J. Mech. Eng. Sci., 200(C5), pp. 367–374. [CrossRef]
Hollingworth, N. E., and Hills, D. A., 1986, “Theoretical Efficiency of a Cranked Link Chain Drive,” Proc. Inst. Mech. Eng., Part C: J. Mech. Eng. Sci., 200(C5), pp. 375–377. [CrossRef]
Kidd, M. D., Loch, N. E., and Reuben, R. L., 1999, “Experimental Examination of Bicycle Chain Forces,” Exp. Mech., 39(4), pp. 278–283. [CrossRef]
Lodge, C. J., and Burgess, S. C., 2002, “A Model of the Tension and Transmission Efficiency of a Bush Roller Chain,” Proc. Inst. Mech. Eng., Part C: J. Mech. Eng. Sci., 216, pp. 385–394. [CrossRef]
Lodge, C. J., and Burgess, S. C., 2004, “An Investigation into the Selection of Optimum Chain and Sprocket Size,” J. Eng. Design, 15(6), pp. 563–580. [CrossRef]
Spicer, J. B., Richardson, C. J. K., Ehrlich, M. J., Bernstein, J. R., Fukuda, M., and Terada, M., 2001, “Effects of Frictional Loss on Bicycle Chain Drive Efficiency,” Trans. ASME, J Mech. Des., 123, pp. 598–605. [CrossRef]
Ariaratnam, S. T., and Asokanthan, S. F., 1987, “Dynamic Stability of Chain Drives,” ASME, J. Mech. Transm., Autom. Des., 109, pp. 412–418. [CrossRef]
Liu, S. P., Wang, K. W., Hayek, S. I., and Trethewey, M. W., 1997, “A Global-Local Integrated Study of Roller Chain Meshing Dynamics,” J. Sound Vib., 203(1), pp. 41–62. [CrossRef]
Shimizu, H., and Sueoka, A., 1975, “Nonlinear Forced Vibrations of Roller Chain,” Bull. JSME, 18(124), pp. 1090–1100. [CrossRef]
Coste, C., and Gilles, B., 1999, “On the Validity of Hertz Contact Law for Granular Material Acoustics,” Eur. Phys. J. B, 7, pp. 155–168. [CrossRef]
Coste, C., and Gilles, B., 2003, “Low-Frequency Behavior of Beads Constrained on a Lattice,” Phys. Rev. Lett., 90(7), p. 174302(4). [CrossRef]
Coste, C., and Gilles, B., 2008, “Sound Propagation in a Constrained Lattice of Beads: High-Frequency Behavior and Dispersion Relation,” Phys. Rev. E, 77, p. 021302(13). [CrossRef]
Job, S., Santibanez, F., Tapia, F., and Melo, F., 2008, “Nonlinear Waves in Dry and Wet Hertzian Granular Chains,” Ultrasonics, 48(6–7), pp. 506–514. [CrossRef] [PubMed]
Sopouch, M., Hellinger, W., and Priebsch, H. H., 2003, “Prediction of Vibroacoustic Excitation Due to the Timing Chains of Reciprocating Engines,” Proc. Inst. Mech. Eng., Part K, J. Multi-Body Dynamics, 217, pp. 225–240. [CrossRef]
Noguchi, S., Nagasaki, K., Nakayama, S., Kanada, T., Nishino, T., and Ohtani, T., 2009, “Static Stress Analysis of Link Plate of Roller Chain Using Finite Element Method and Some Design Proposals for Weight Saving,” J. Adv. Mech. Des., Systems and Manufacturing3(2), pp. 159–170. [CrossRef]
Norden, B. N., 1973, “On the Compression of a Cylinder in Contact With a Plane Surface,” Technical Report No. NBSIR 73-243, U.S. Department of Commerce, National Bureau of Standards, Washington, DC.
Puttock, M. J., and Thwaite, E. G., 1969, “Elastic Compression of Spheres and Cylinders at Point and Line Contact,” National Standards Laboratory Technical Paper No. 25, Commonwealth Scientific and Industrial Research Organization (CSIRO), Melbourne, Australia.
Castillo, J., and Barber, J. R., 1997, “Lateral Contact of Slender Prismatic Bodies,” Proc. R. Soc. London, Ser. A, 453, pp. 2397–2412. [CrossRef]
Persson, A., 1964, “On the Stress Distribution of Cylindrical Elastic Bodies in Contact,” Ph.D. dissertation, Chalmers University of Technology, Göteborg, Sweden.
Ciavarella, M., and Decuzzi, P., 2001, “The State of Stress Induced by the Plane Frictionless Contact. I. The Case of Elastic Similarity,” Int. J. Solids Struct., 38, pp. 4507–4523. [CrossRef]
Wilson, H. B., and Hill, J. L., 1972, “Non-Hertzian Contact Stresses in a Smoothly Cradled Heavy Cylinder,” J. Elast., 2(2), pp. 143–151. [CrossRef]
Woodward, W., and Paul, B., 1976, “Contact Stresses for Closely Conforming Bodies—Application to Cylinders and Spheres,” Technical Report No. DOT-TST-77-48, U.S. Department of Transportation, Office of the Secretary, Office of University Research, Washington, DC.
Nowell, D., Hills, D. A., and Sackfield, A., 1988, “Contact of Dissimilar Elastic Cylinders Under Normal and Tangential Loading,” J. Mech. Phys. Solids, 36(1), pp. 59–75. [CrossRef]
Tsubakimoto Chain Company, 2006, “The Complete Guide to Chain,” Reference Handbook, Osaka, Japan, http://chain-guide.com/toc.html
Standards Committee Meeting, 1921, “Chain Division Report, Roller Chain Sprockets,” J. Soc. Automotive Eng., 9(1), pp. 55–57.


Grahic Jump Location
Fig. 1

Schematic illustration of the nonlinear, spring-mass system used to model the elastic response of bicycle chain. The masses correspond to chain half-links (assumed to have equal masses) and the springs correspond to contacts at pin-bushing interfaces.

Grahic Jump Location
Fig. 2

Schematic illustration of chain link components (some are omitted for clarity of illustration) and the corresponding geometrical quantities used to describe Hertzian contact at the pin-bushing interface

Grahic Jump Location
Fig. 3

Measured chain extension as a function of applied load (points) for a commercially-available bicycle chain compared to the results of modeling chain stiffness using Hertzian contact mechanics (solid curve). Equation (14) was fit to the measured chain response by adjusting values for physical parameters.

Grahic Jump Location
Fig. 4

Chain transmission efficiency as a function of the reciprocal of the chain tension derived from Eqs. (13) and (15). Efficiency is shown for various pin-bushing clearance parameters. Measurements of commercially-available chains indicate that pin-bushing clearances can be within the range shown, 0.00125–0.01 mm−1.

Grahic Jump Location
Fig. 5

Variation of chain transmission efficiency as a function of the Young's modulus of the pin and bushing—both are assumed to have the same stiffness. Efficiency is shown for three different chain tensions. For these results, the Poisson ratio has been fixed at 0.29 and the pin-bushing clearance parameter was 0.003 mm−1.

Grahic Jump Location
Fig. 6

Measured chain extension as a function of applied load (points) for a commercially-available bicycle chain compared to the results of modeling chain stiffness using Hertzian contact mechanics (solid curve) or using a hyperbolic fit (dashed curve). Either model can be used to represent the measured chain behavior but each yields distinct values for the chain stiffnesses.

Grahic Jump Location
Fig. 7

Chain transmission efficiency as a function of the reciprocal of the chain tension. Data points represent actual measurements performed on a derailleur-type chain drive operating in the offset condition for the sprocket combinations noted, 52-21 and 52-11 (number of teeth on the proximal-distal sprockets) [7]. Solid curves represent calculations of efficiency using Eq. (13) along with chain stiffnesses based on the hyperbolic chain extension model.




Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In